APPLICATION
Jointex^® is used as an expansion / contraction joint former.

ADVANTAGES

Jointex^® has good compression qualities with good recovery
     capacity.

Jointex^® is supplied with a hinged temporary blocking piece,
     leaving a clean, neat and perfectly sized groove providing
     a consistent depth channel for joint sealent.

Jointex^® is cut to size, eliminating wastage and cutting

     on site.

The Jointex^® material is flexible and can be used around

     corners.

Jointex^® Excellent resistance to chemicals.

Jointex^® is waterproof, does not disintegrate, rot or swell.

No bond breaker required.

JOINTEX^® PHYSICAL PROPERTIES / TECHNICAL DATA

JOINTEX^® PRODUCT CODES AND SIZES

DIRECTIONS FOR USE

Ensure all concrete surfaces are free from base grit and dust.

Apply glue in vertical strips ± 100 mm wide and 25 mm from the top to avoid the tear-off strip from sticking to the concrete face.

Allow the glue to dry (according to manufacturer’s instructions) and then stick Jointex^® onto the glued concrete face.

Cast the next section of concrete as required. Take care not to let the wet concrete get behind Jointex^® as this will result in a
     wavy joint.

When the joint sealant is about to be applied, simply peel the tear-off strip out of the formed joint, leaving an even groove of
     uniform depth for filling with sealant.

Please Note: In conjunction with water retaining structures, Jointex^® must NOT be used where the water head is in excess of 3 metres. Use Aquajoint (SPX 120) for applications where the water head exceeds 3 metres and is not more than 15 metres.

Plastic Rebar Spacers and Concrete Rebar Spacers for Rebar
We supply a wide range of plastic spacers and concrete spacers for the rebar and construction industries, such as:
1.   Plastic Spacers for Rebar
2.   Concrete Spacers for Rebar
3.   Circular Plastic Spacers for Rebar Columns
4.   Plastic Centralisers for Rebar
5.   Fibre Cement Spacers for Rebar


Formwork and Scaffolding Accessories
We supply formwork and scaffolding accessories, to the Formwork and scaffolding industries, such as:
1.   Base Jack Nuts for Scaffolding
2.   Base Jacks for Scaffolding
3.   Ferrule dollies for light Formwork
4.   Ferrule Jacks for Light Formwork
5.   Swivel Couplers for Scaffolding
6.   Fixed Couplers for Scaffolding
7.   T Bolts for Scaffolding Couplers
8.   Tie Rods for Formwork
9.   Corner Fillets with lip for Formwork economy panels
10. Chamfer with lip for Formwork economy panels
11. Plain Chamfer for Formwork economy panels
12. Water Stoppers for Formwork

Rebar Processing Equipment and Rebar Accessories
We also supply a wide range of rebar processing equipment and accessories, to the rebar processing and rebar placement industries, such as these Rebar Cutters:
1.   DC-16LZ Rebar Cutter - 220V
2.   DC-16W Rebar Cutter - 220V
3.   DC-20HL Rebar Cutter - 220V
4.   DC-20W Rebar Cutter - 220V
5.   DC-20WH Rebar Cutter - 220V
6.   DC-25X Rebar Cutter - 220V
7.   DC-25W Rebar Cutter - 220V
8.   DC-32WH Rebar Cutter - 220V
9.   M26 Rebar Cutter - 380V
10. M36 Rebar Cutter - 380V
11. M45 Rebar Cutter - 380V
12. MG20H Rebar Cutter - 220V

and these Rebar Benders:
1.   DBD-16L Rebar Bender - 220V
2.   DBD-25H Rebar Bender - 220V
3.   DBD-32X Rebar Bender - 220V
4.   B26 Rebar Bender - 380V
5.   B36 Rebar Bender - 380V
6.   B45 Rebar Bender - 380V
7.   MG20B Rebar Bender - 220V

and Combination Rebar Cutters and Benders:
1.   Manual Rebar Cutter Bender
2.   Mobile Rebar Cutter Bender - Powered by own generator.
3.   DBC-16H Rebar Cutter Bender - 220V
4.   DBC-25X Rebar Cutter Bender - 220V
5.   MG20HB Rebar Cutter Bender - 220V

Special Items such as Wire Grips:
1.   Nagaki Wire Grips